1. Creation des VLAN
-Switch 1:
Switch>enable
Switch#conf t
Switch(config)#hostname S1
S1(config)#vlan 10
S1(config-vlan)#exit
S1(config)#vlan 20
S1(config-vlan)#exit
S1(config)#vlan 30
S1(config-vlan)#exit
S1(config)#vlan 99
S1(config-vlan)#exit
-Switch 2:
Switch>ENable
Switch#conf t
Switch(config)#hostname S2
S2(config)#vlan 10
S2(config-vlan)#exit
S2(config)#vlan 20
S2(config-vlan)#vlan 30
S2(config-vlan)#vlan 99
S2(config-vlan)#exit
S2(config)#
-Switch 3:
Switch>enable
Switch#conf t
Switch(config)#hostname S3
S3(config)#vlan 10
S3(config-vlan)#vlan 20
S3(config-vlan)#vlan 30
S3(config-vlan)#vlan 99
S3(config-vlan)#exit
S3(config)#
2. Assignation des ports aux VLANs
-Switch 1:
S1(config)#interface range fastEthernet 0/3-11
S1(config-if-range)#switchport mode access
S1(config-if-range)#switchport access vlan 10
S1(config-if-range)#exit
S1(config)#interface range fastEthernet 0/12-20
S1(config-if-range)#switchport mode access
S1(config-if-range)#switchport access vlan 20
-Switch 2:
S2(config)#interface range fastEthernet 0/3-11
S2(config-if-range)#switchport mode access
S2(config-if-range)#switchport access vlan 20
S2(config-if-range)#exit
S2(config)#interface range fastEthernet 0/12-20
S2(config-if-range)#switchport mode access
S2(config-if-range)#switchport access vlan 30
-Switch 3:
S3(config)#interface range fastEthernet 0/3-11
S3(config-if-range)#switchport mode access
S3(config-if-range)#switchport access vlan 10
S3(config-if-range)#exit
S3(config)#interface range fastEthernet 0/12-20
S3(config-if-range)#switchport mode access
S3(config-if-range)#switchport access vlan 30
3-Mode Trunk entre les Switchs
-Switch 1:
S1(config)#interface range fastEthernet 0/1-2
S1(config-if-range)#switchport mode trunk
-Switch 2:
S2(config)#interface range fastEthernet 0/1-2
S2(config-if-range)#switchport mode trunk
-Switch 3:
S3(config)#interface range fastEthernet 0/1-2
S3(config-if-range)#switchport mode trunk
4-Activer Routage Inter Vlan On a Stick:
-Switch 2:
S2(config)#interface fastEthernet 0/24
S2(config-if)#switchport mode trunk
-R1:
R1(config)#interface gigabitEthernet 0/0
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#interface gigabitEthernet 0/0.10
R1(config-subif)#encapsulation dot1Q 10
R1(config-subif)#ip address 192.168.10.1 255.255.255.0
R1(config-subif)#no shutdown
R1(config-subif)#exit
R1(config)#interface GigabitEthernet0/0.20
R1(config-subif)#encapsulation dot1Q 20
R1(config-subif)#ip address 192.168.20.1 255.255.255.0
R1(config-subif)#no shutdown
R1(config-subif)#exit
R1(config)#interface GigabitEthernet0/0.30
R1(config-subif)#encapsulation dot1Q 30
R1(config-subif)#ip address 192.168.30.1 255.255.255.0
R1(config-subif)#no shutdown
R1(config-subif)#exit
R1(config)#interface GigabitEthernet0/0.99
R1(config-subif)#encapsulation dot1Q 99
R1(config-subif)#ip address 192.168.99.1 255.255.255.0
R1(config-subif)#no shutdown
Partie Routage InterVlan Existant:
1- Creation des Vlans
Switch 4
Switch>enable
Switch#conf t
Switch(config)#hostname S4
S4(config)#vlan 100
S4(config-vlan)#vlan 200
S4(config-vlan)#vlan 300
S4(config-vlan)#exit
Switch 5
Switch>enable
Switch#conf t
Switch(config)#hostname S5
S5(config)#vlan 100
S5(config-vlan)#vlan 200
S5(config-vlan)#vlan 300
S5(config-vlan)#exit
Switch 6
Switch>enable
Switch#conf t
Switch(config)#hostname S6
S6(config)#vlan 100
S6(config-vlan)#vlan 200
S6(config-vlan)#vlan 300
S6(config-vlan)#exit
2. Assignation des ports aux VLANs
Switch 5:
S5(config)#interface range fastEthernet 0/3-9
S5(config-if-range)#switchport mode access
S5(config-if-range)#switchport access vlan 100
S5(config-if-range)#exit
S5(config)#interface range fastEthernet 0/10-15
S5(config-if-range)#switchport mode access
S5(config-if-range)#switchport access vlan 200
S5(config-if-range)#exit
S5(config)#interface range fastEthernet 0/16-20
S5(config-if-range)#switchport mode access
S5(config-if-range)#switchport access vlan 300
S5(config-if-range)#exit
S5(config)#
Switch 6:
S6(config)#interface range fastEthernet 0/3-9
S6(config-if-range)#switchport mode access
S6(config-if-range)#switchport access vlan 100
S6(config-if-range)#exit
S6(config)#interface range fastEthernet 0/10-15
S6(config-if-range)#switchport mode access
S6(config-if-range)#switchport access vlan 200
S6(config-if-range)#exit
S6(config)#interface range fastEthernet 0/16-20
S6(config-if-range)#switchport mode access
S6(config-if-range)#switchport access vlan 300
S6(config-if-range)#exit
3-Mode Trunk entre les Switchs
Switch 4:
S4(config)#interface range fastEthernet 0/1-2
S4(config-if-range)#switchport Mode Trunk
Switch 5:
S5(config)#interface range fastEthernet 0/1-2
S5(config-if-range)#switchport Mode Trunk
Switch 6:
S6(config)#interface range fastEthernet 0/1-2
S6(config-if-range)#switchport Mode Trunk
4-Activer Routage Inter Vlan Existant:
Switch 4:
S4(config)#interface fastEthernet 0/21
S4(config-if)#switchport mode access
S4(config-if)#switchport access vlan 100
S4(config-if)#exit
S4(config)#interface fastEthernet 0/22
S4(config-if)#switchport mode access
S4(config-if)#switchport access vlan 200
S4(config-if)#exit
S4(config)#interface fastEthernet 0/23
S4(config-if)#switchport mode access
S4(config-if)#switchport access vlan 300
S4(config-if)#exit
S4(config)#
R2:
Router>Enable
Router#conf t
Router(config)#hostname R2
R2(config)#interface gigabitEthernet 0/0
R2(config-if)#ip address 172.16.10.1 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface gigabitEthernet 1/0
R2(config-if)#ip address 172.16.20.1 255.255.255.0
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface gigabitEthernet 2/0
R2(config-if)#ip address 172.16.30.1 255.255.255.0
R2(config-if)#no shutdown
Partie Rip
R1:
R1>ENable
R1#CONF T
R1(config)#interface serial 0/0/0
R1(config-if)#ip address 10.1.1.1 255.255.255.252
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 10.1.1.0
R1(config-router)#network 192.168.10.0
R1(config-router)#network 192.168.20.0
R1(config-router)#network 192.168.30.0
R1(config-router)#network 192.168.99.0
R1(config-router)#
R2:
R2(config)#interface serial 4/0
R2(config-if)#ip address 10.1.1.2 255.255.255.252
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#network 10.1.1.0
R2(config-router)#network 172.16.10.0
R2(config-router)#network 172.16.20.0
R2(config-router)#network 172.16.30.0
R2(config-router)#
Maintenant le ping passera entre tous les PCs
Partie SSH:
-Switch 3:
S3>enable
S3#conf t
S3(config)#interface vlan 99
S3(config-if)#ip address 192.168.99.2 255.255.255.0
S3(config-if)#no shutdown
S3(config-if)#exit
S3(config)#ip default-gateway 192.168.99.1
S3(config)#username admin password ccna
S3(config)#ip ssh version 2
S3(config)#ip domain-name cisco
S3(config)#crypto key generate rsa
The name for the keys will be: S3.cisco
Choose the size of the key modulus in the range of 360 to 2048 for your
General Purpose Keys. Choosing a key modulus greater than 512 may take
a few minutes.
How many bits in the modulus [512]: 1024
S3(config)#line vty 0 4
S3(config-line)#transport input ssh
S3(config-line)#login local
S3(config-line)#exit
S3(config)#
Tester le SSH dans n' importe quel PC:
C:\>ssh -l admin 192.168.99.2
Open
Password:
S3>en
S3>enable
